Drum Motor & Idler Dimensions
Bracket Dimensions
Optional Cable Type Dimensions
Drum Motor Specifications
Cross Sectional Diagram
Parts Description

Dimensions (in inches)

Drum Motor
TM160A30

Drum Motor
TM160B30

Idler
KT160A30

Idler
KT160B30

Standard face widths (L) in inches for the TM160A30 and KT160A30: 13.73*   15.75   16.73   17.72   19.69   21.65   23.62   25.59   27.56   29.53   31.50   33.46   35.43   37.40 

Standard face widths (L) in inches for the TM160B30 and KT160B30: 15.75*   16.73*   17.72   19.69   21.65   23.62   25.59   27.56   29.53   31.50   33.46   35.43   37.40 

*This face width is not available in all horsepower.

back to top

Bracket AB 30

Optional Cable Type

Note: When Optional Cable Type is selected, the minimum face width (L) increased by 1.969 inches.

back to top

Specifications

Type	HP	Belt speed in feet per minute (ft/min) Belt pull measured in pounds (lbs.)														Minimum length (L) in inches		Weight in pounds (lbs.) at L = 13.78 inches
																Design A	Design B
TM160 - 22	2.00	935	782	652	593	489	397	354	317	295	274	265	241	215	(ft/min)	13.78	15.75	67.10
		66	79	95	104	126	156	186	195	209	225	233	256	287	(belt pull)
		203	189	*160	*146	(ft/min)
		304	327	410	448	(belt pull)
TM160 - 42	2.00	468	392	326	298	243	198	177	158	151	139	132	120	109	(ft/min)	15.75	17.72	68.50
		132	157	189	208	253	311	368	391	408	443	467	512	568	(belt pull)
		102	94	*80	*73	(ft/min)
		608	653	825	904	(belt pull)
TM160 - 415	1.50	468	392	326	298	243	198	177	158	151	139	132	120	109	(ft/min)	13.78	15.75	67.10
		99	118	142	156	190	233	279	293	306	332	350	384	426	(belt pull)
		102	94	*80	*73	(ft/min)
		456	490	575	630	(belt pull)
TM160 - 41	1.00	468	392	326	298	243	198	177	158	151	139	132	120	109	(ft/min)	13.78	15.75	64.90
		66	79	95	104	127	156	174	195	204	221	233	256	284	(belt pull)
		102	94	80	73	(ft/min)
		304	327	384	421	(belt pull)
TM160 - 61	1.00	312	262	217	198	163	132	118	106	99	92	87	80	71	(ft/min)	15.75	17.72	68.50
		99	117	143	156	189	233	261	291	311	335	353	384	436	(belt pull)
		69	64	54	*47	(ft/min)
		451	484	568	702	(belt pull)
TM160 - 475	0.75	468	392	326	298	243	198	177	158	151	123	102	109	102	(ft/min)	13.78	15.75	63.80
		49	59	71	78	95	117	131	146	160	188	192	213	228	(belt pull)
		94	80	73	(ft/min)
		245	288	316	(belt pull)
TM160 - 675	0.75	312	262	217	198	163	132	118	106	99	92	87	80	71	(ft/min)	13.78	15.75	67.10
		74	88	107	117	142	175	196	218	233	251	265	288	327	(belt pull)
		69	64	54	47	(ft/min)
		338	363	426	489	(belt pull)
TM160 - 875	0.75	234	196	163	149	123	99	90	78	61	52	50	47	40	(ft/min)	15.75	17.72	68.50
		100	124	149	164	198	245	270	312	400	472	490	522	614	(belt pull)
		35	(ft/min)
		702	(belt pull)
TM160 - 605	0.50	312	262	217	198	163	132	118	106	99	92	87	80	71	(ft/min)	13.78	15.75	64.90
		49	59	71	78	95	117	131	145	165	175	185	192	218	(belt pull)
		69	64	54	47	(ft/min)
		225	242	284	327	(belt pull)
TM160 - 805	0.50	234	196	163	149	123	99	90	78	61	52	50	47	40	(ft/min)	13.78	15.75	67.10
		66	79	94	104	125	156	172	199	251	297	312	326	384	(belt pull)
		35	(ft/min)
		435	(belt pull)
TM160 - 634	0.34	312	262	217	198	163	132	118	106	99	92	87	80	69	(ft/min)	13.78	15.75	63.80
		34	40	48	53	64	79	89	99	110	120	125	138	153	(belt pull)
		94	54	47	(ft/min)
		165	193	222	(belt pull)
TM160 - 834	0.34	234	196	163	149	123	99	90	78	61	52	50	47	40	(ft/min)	13.78	15.75	67.10
		45	54	64	71	85	106	117	135	171	202	212	222	261	(belt pull)
		35	(ft/min)
		296	(belt pull)
TM160 - 1213	0.13	151	125	104	94	78	64	57	52	40	33	31	26	24	(ft/min)	13.78	15.75	64.90
		27	32	39	42	51	63	71	77	100	121	131	154	170	(belt pull)
* Please consult the Van der Graaf technical department for use of these speeds. - Other belt speeds and face widths are available. - The total weight of the unit increases by 1.4 pounds per inch above 13.78 inches. - When the drive is supplied with lagging, the covered face width is reduced by 0.87 inches. - Belt speed is measured on the center of the unit without lagging. - Listed belt speeds are under full load conditions and may be higher under no load conditions. - When an electromagnetic brake is required, the minimum face width is increased by 3.94 inches. NOTE: TM160 type drum motors are available in all standard voltages and are electrically reversible.

back to top

Cross Sectional Diagram & Parts Description

Position Number	Part Description	Position Number	Part Description
1	Shell	33	Socket Head Cap Screw
2A	End Flange	34	Filler Plug
2B	End Flange	35	Washer
3	Gear Housing	36	Ball Bearing
4	Motor Flange	36V	Cylindrical Bearing
6	Shaft End	37	Ball Bearing
7	Hollow Shaft	37A	Ball Bearing
8Z	Internal Gear	38	Ball Bearing
9/10	Pinion with Bushing	39	Needle Bearing
11	Gear	40	Shim
12	Distance Ring	41	Locking Disc
13	Stator	42	Snap Ring
14	Rotor	43	Snap Ring
15	Socket Head Cap Screw	44	Snap Ring
16	Cable Passage	45A	Bearing Race
18	Gasket	45B	Bearing Race
20	Terminal Board	45DS	Double Seal Adaptor
23	Fillister Head Machine Screw	46	Oil Seal
24	Fillister Head Machine Screw	50	Seal
27	Set Screw	51	Junction Box
28	Set Screw	52	Junction Box Cover
29	Key	53	Plug
31	Socket Head Cap Screw	55	Backstop Bearing
32	Washer Copper	57	Name Plate

back to top


This site is designed and built by Van der Graaf © 2001. All rights reserved.